more | Lenz BM3 Block Section Module (22620)
Price information not yet available
The BM3 is a BM2 module which has been equipped with block section control. This allows prototypical block section operation. The number of blocks is not restricted as one BM3 is used for every block more.. | |
more | Lenz TR100 Transformer 15v. 3amp. 45VA. (26001)
A 45VA insulated transformer capable of an output of 3 amps. Ideal for powering the Lenz Compact, LH90 and LH100 control units on smaller layouts.
Fitted with UK plug | |
more | Lenz TR150 Transformer 15V. 4.6amp. 70VA. (26151)
A 70VA insulated power transformer with an output of 15 volts and a maximum of 4.6amps.
This unit is recommened for use with the Lenz LH90 and LH100 control systems when used on larger layout operating multiple locomtoives.
This transformer should also be selected for use with the Lenz LV102 power amplifier/booster to ensure that the amplifiers full rated current can be supplied.
Fitted with UK plug | |
more | Lenz LS100 Switch Module 4 Points/Signals Feedback (11100)
The accessory decoder receives the commands send by the central command station through the power module and, for example, controls the switch machines on your turnouts (or the other devices). The commands are initiated from your input devices, such as the Basic Hand Held LH100, the Tower Cab LW100, the Computer Interface LI100 or the command station converter module LC100 (in connection with an Arnold or Märklin Digital system).
The accessory decoder LS100/LS110 are equipped with 4 outputs, with 3 terminals (+,C,-) each. These outputs can be connected to 4 twin-coil switch machines (or twin-coil actuators for your signals).more.. | |
more | Lenz LS150 Point Decoder (11150)
6 outputs of up to 3 amps, Overload Protection, Pulse Duration variable from 0.1 to 10 seconds. Addresses easily set using programming button.
Using cheap diodes (not included), motorised points such as Tortoise, Fulgurex etc can be used. | |
more | Lenz LR101 Feedback Module (8 sections) (11201)
The LR101 sends information back to the command station LZ100, such as occupancy of a block or activation of a contact. Information stored in the command station can be accessed by any unit linked to the XpressNet, for example the Hand Held LH100, the Tower Cab LW100 or by software through the Computer Interface LI100F. more.. | |
more | Lenz LB101 Current Detection Unit (11210)
LB101 reports occupancy status in track sections to the encoder LR101. It operates on the so called "current sensing principle", that is there is always feedback when a current user is in the monitored track section (detection section)more.. | |
more | Lenz LK100 Reverse Loop Module (12100)
Developed to simplify the wiring of reversing loops on two-rail DC layouts using NMRA Digital Command Control by allowing you to operate your trains through a reversing section/loop without manually changing locomotive direction or track polarity. | |
more | Lenz Digital Filter (13150)
Filter unit to permit trains to pass from a conventional DC controlled layout section to a section under DCC command control without causing a short circuit or damage to DCC electronics.more.. | |
more | Lenz LV102 Amplifier (22102)
The 5 amp LV102 has programmable DCC track voltages from 11 volts DCC to 22 volts DCC in 1/2 volt increments, and is equipped with a RP-9.3.1 (revised) cutout for use with RailCom. The LV102 has a current rating of 5 amps, 4.4 amps continuous at 50 degrees C | |
more | Lenz BM1 Block Section Module (22600)
The BM1 has been designed for the simplest and therefore most cost-effective solution for stopping at a signal. The application is incredibly simple. If the signal is at "STOP”, the track voltage is directed via the BM1. The BM1 generates an asymmetry in the otherwise symmetrical digital voltage. This asymmetrical signal is detected by the new GOLD series decoders. The result is a gentle braking of the train until it comes to a halt, optionally with the set braking delay or set braking distance. If the train approaches the signal from the opposite direction, it simply continues because the asymmetry is detected depending on the direction of movement. If the signal changes to "CLEAR", the BM1 is bridged by the signal switch and the train accelerates at the speed set in the decoder to the DCC instructed speed.more.. | |
more | Lenz USB Interface (23150)
The Interface enables you to connect your Lenz Set to a computer. You can then run your layout from a PC with Windows 2000 or XP using a proprietary programme such as Windigital or Railroad and Co and others. You can put a track diagram on the screen, change points, drive trains and do all sorts of other very clever things. more.. | |
more | Lenz XPA XpressNet Phone Adaptor (23201)
Using our XPA (XpressNet Phone Adapter) you can convert any wireless phone into a fully functional throttle providing a afordable wireless option with excellent range and realibility. The XPA can be used on any XpressNet System (Roco, Lenz and Atlas). | |
more | Lenz LY001 Set of Plugs 3, 4, 6 Way (80001)
| |
more | Lenz LA152 XBUS Adaptor with Faceplate (80152)
The LA152 provides an easy method to install XpressNET ports in convenient locations anywhere on your layout. more.. | |
Model Railways
Search
Index
Checkout
Back