Recommended for expanding model railways

An excellent twin-track power controller unit, with power outputs for accessories also provided, allowing point motors to be connected without needing another power supply. The power transformer is incorporated into the controller, it has a 240-volt AC power cable and plug attached, no separate transformer unit is required.

Connects to mains and provides high output speed control for two loco's running on seperate tracks - extendable to four by adding extra slave control units. 16v AC & 12v DC power outputs for signals and lights are also provided.

This is the one! If you require a good standard railway controller that is capable of running most normal model railway layouts then this is it.

Recommended single-track train controller.

A 12-volt DC single track controller, analogue, supplied with a plug-top mains power transformer, track power connection clip and simple plug-in wiring.
The controller has a large knob for speed control and a long flat slide switch for direction control, making running the trains easy and fun for children and adults alike. Will control all standard locomotives from Hornby, Bachmann, Graham Farish, Dapol and most other manufacturers.

Output 12V DC controlled, 0.7Amps

A 12-volt DC single track controller, supplied with a plug-top mains power transformer. Outputs from the controller are 12-volts DC controlled track power from train speed control and 16-volts AC uncontrolled to supply accessories such as point motors.
The controller has a large knob for speed control and a long flat slide switch for direction control, making running the trains easy and fun for children and adults alike.

Low cost train controller allowing forward and reverse with proportional speed control. Requires a 16v AC input from a Hornby C990 plug in wall transformer. The output is 12v DC controlled plus it has a 16v output for operating points, signals etc.

An inexpensive starter option.

Requires C990 mains transformer.

Standard 16v AC wall mounted plug top transformer unit. This is the power supply for Hornby R965 train controller and Scalextric racing powerbase controllers.

An uncomplicated controller which comes complete with a separate, dedicated transformer plugging directly into a wall socket with a 1.8m lead to plug into the controller. The Combi can be screwed to either a panel or direct to the baseboard. This means that small layouts which have to be put away will not be encumbered with trailing wires & heavy transformers. The casings are made from high impact ABS & the control circuits give the same running characteristics as our traditional controllers.
The transformer is available separately as model WM1.

Twin Track Panel Mount Controller with Feedback for most small Gauges
Input: 2 x 16v A.C. at 1.25 amps Requires 2x T1 or 2x M1 Transformers
Output: 2 x 12v D.C. at 1 amp each controlled
Measurements: Panel: 120mm x 105mm x 15mm deep
Aperture: 100mm x 69mm x 15mm deep

Not recommended for use with coreless design motor

Single Track Panel Mount Controller for ‘N’, ‘OO’ and most small Gauges
Input: 1 x 16v A.C. at 1.25 amps Requires T2, M2 transformer                                                                       Output: 1 x 14v D.C. at 1 amp controlled
Measurements: Panel: 70mm x 105mm x 28mm deep
Aperture: 43mm x 83mm x 25mm deep

Single track hand-held or walkabout type controller with feedback, suitable for most small gauges.
Input:1 x 16v A.C. at a maximum of 1.25 amps Requires T1, M1 Transformer, or 100M Controller
Output: 1 x 12v D.C. at 1 amp controlled
Measurements: 75mm x 50mm x 27mm deep
Fitted with 1.5 metres of 4 core cable

Not recommended for use with coreless design motors

The casing is made from high impact ABS
Input: Mains (240v A.C.)
Output: 1 x 18v A.C. at 1.1 amp
Measurements: 65mm x 80mm x 83mm

A useful AC transformer ideal for providing power for controllers and point motor supplies. Two 16-volt output windings are provided at a maximum output of 1.25amps.

Please note that this transformer must be installed inside an enclosure suitable for mains power use.

Open Construction Transformer
Input: Mains (240v A.C.) use 3 amp fuse
Requires own mains lead & plug to be fitted
Output: 1 x 12v A.C. at 5 amps
Requires own wires and cutouts as necessary