A useful introduction to DCC decoder installation, complete with an illustrated??guide, showing how decoders can??be fitted to??British OO models. Popular models from??Lima, Hornby??and Bachmann are used to illustrate the fitting of decoders to differing chassises and motor designs - from open frame motors to??split chassis systems. Fit decoders to older models with confidence.

A budget priced DCC decoder with two additional function controls. Fitted with a NEM plug for fitting to DCC Ready locomotives.

Length 26mm, Width 17mm, Height 7mm. Wire length 70mm

Designed for use with the 21-pin connectors fitted to many of the most recent models this three function decoder offers several advanced features including configurable back EMF high-frequency pulse width motor speed control. A shunting speed function control is provided, allowing finer control for slow speed operations.

Decoder measures 24mm long, 15mm wide with socket at one end.

A high quality DCC decoder with a wide range of user configurable CVs allowing the decoder to be tuned and matched to most model railway locomotive motors.

Fitted into a miniature package measuring just 13.5 x 10 x 3.5mm with 6-pin NEM651 connection the decoder offers 0.5A motor output and two function outputs totalling 100mA. CVs allow for short (2 digit) or long (4 digit) addressing plus adjustment of motor back EMF control response and speed curve modifiction.

Now used on almost all new design N gauge model locomotives, Bachmann plan to incorporate the NEM651 socket into small OO locomotives.

A pack of three 1-amp locomotive decoder with a bare wire harness, ideal for locomotives requiring a hard-wired decoder instalation.

Length 23mm, Width 16mm, Height 3.5mm. Wire length 70mm

A budget priced two function decoder with 9-pin plug and wiring harness for locomotives not fitted with DCC sockets.

Even this??low price??decoder still incorporates TCS's slow speed dither control and quiet drive functionality.

1.3A continuous 2A peak motor output. Two 100mA function outputs. Connection - wire
Measures 26 x 16 x 4mm

A very small locomotive decoder with 8-pin plug. Offering smooth operation in 14, 28 or 128 step modes and an outstanding power output capabilty of 1A continuous, with 2A peak. 2 function outputs atotalling ???A are available and a short length harness is fitted. Ideal for many models where the decoder can be fitted close to the plug socket.

Decaoder measures 11mm length, 9mm width, 3mm thickness.

The 6-pin plug-in decoder has been designed specifically to be accomodated inside N gauge locomotives, many of which are now being supplied with a socket for these decoders.

Decoder measures 10mm length (15mm over pins), 8.5mm width, 3mm thickness.

Next delivery delayed until September.

A new version of the Hornby 4-function DCC locomotive decoder featuring extended addressing and enhanced NMRA compatibility.

Supplied with the normal 8-pin plug the decoder can support 4 auxiliary functions in addition motor control. Decoder measures 17mm x 10mm x 3.5mm.

The Hornby Sapphire will offer many, if not more features, including RailCom?? than the Digital enthusiast would expect from a top of the range decoder.This addition to the Hornby Digital range of products is a positive step towards Hornby's commitment to Digital control for model railways.

A high specification decoder with a wide range of configuration options the sapphire has a 21-pin socket connection and is supplied with a wire harness to an 8-pin plug. Decoder measures 23 x 16.5 x 6.5mm.

This DCC decoder adapter allows a decoder with an 8-pin plug to be connected with locomotives fitted with 21-pin sockets.

Antics can supply your new DCC Ready OO gauge locomotive with the decoder installed!
At an extra charge of just ?£10.00 we can fit a decoder to a DCC Ready locomotive, needing only the programming of a suitable unused address to be done by you. Select your DCC Ready OO gauge locomotive, then add this service to your order, either selecting a decoder or requesting us to supply a suitable decoder (use the other instructions box of the checkout screen).
We will deliver your DCC locomotive with the decoder fitted and tested.

Terms and Conditions Apply. Service available to web customers and at some shops only. Please ask the staff in store.

Ideal for fitting decoders to older locomotives not equiped with sockets without the risk of accidental damage to the???decoder during soldering.

This wiring harness has fittings to connect a NEM651 6-pin decoder, commonly used with N gauge models. Many of these decoders have a power rating easily able to drive OO model locomotives and ths small size makes these decoders a good choice for small engines.

A useful adapter from Bachmann, providing the option to fit a 6-pin decoder to a model with an 8-pin socket.

This can be useful on models with restricted space for the decoder, as on many steam locomotives, providing???the option of fitting a small footprint 6-pin decoder, designed to fit inside the body of an N gauge model.