more | Peco Mounting Plates for PL10 (x5) (PL9)
A set of five mounting plates with attachment slots for PL10 point motors. This allows the motor to be mounted beneath the baseboard, avoiding the need to make a large hole to accomodate the motor directly beneath the point. | |
more | Peco Point (Turnout) Motor Extended Pin (PL10E)
The PL10-E point motor is fitted with a long point operating pin, ideal for mounting beneath baseboards. A small 10mm (3/8in) hole through the baseboard is required, located directly beneath the operating pin attachment location on the point. The pin will then reach through the board and locate into the operating pin attachment hole of the point. The pin can then be trimmed to length with a good side or track cutter tool. Peco strongly recommend that the PL10E be used in conjunction with a PL-9 Mounting Plate, fitted directly to the base board underneath the point. Operation is from a passing contact switch or probe and stud system to give a pulse from the 16v AC outlet found on most transformers (2 amps required). If this isn't available an uncontrolled 12v DC supply may suffice. A constant current would burn out the motor. | |
more | Peco Point (Turnout) Motor High Performance (PL10W)
This point motor is designed to operate with the lower amperage found on some European transformers or with DCC systems*. Operation is from a passing contact switch or probe and stud system to give a pulse from the 16v AC outlet found on most transformers. If this isn't available an uncontrolled 12v DC supply may suffice. A constant current would burn out the motor.
* Although the initial amperage from DCC systems is very high, say 10 amps, the final amps avaialble to accessories such as point motors is very low, once the current has passed through the booster units used in DCC systems. more.. | |
stock
info | Peco Point (Turnout) Motor Low Current Extended Pin (PL10WE)
A new point motor type from Peco incorporating the extended operating pin, allowing the motor to be mounted to the underside of baseboards, with the low current solenoid design.
These motors have a lower power consumption, designed with DCC systems in mind allowing these motors to be controlled by point/accessory decoders. more.. | |
more | Peco Point Motor Adaptor Base for PL10 Motors (PL12)
Adaptor base to accept PL10 type point motors for either above or below base board use, includes an over centre spring, as fitted to all Peco turnouts.
1. If it is wished to fit the turnout motor above the baseboard, rather than below, then the adaptor base is used. An extension arm included allows the motor to be positioned up to 40mm away from the track. The point's over centre spring has to be removed as that in the base takes over. The whole unit, including motor, can be disguised by placing a small building, such as an LK-4 Lineside Hut, over it.
2. If the modeller wishes to power non-PECO points which do not have the over centre spring action. The adaptor base is positioned underneath the point and the PL-10E is attached to it, allowing the the point to be operated as if it were PECO. more.. | |
more | Peco Accessory Switch (PL13)
This is an accessory switch that connects directly to the point, thus allowing operation with the movement of the point blades. Used in many situations such as to provide electrical switching for frog polarity, signals etc. | |
more | Peco Twin Micro Switch Kit (PL15)
This twin microswitch kit provides two sets of switched contacts so that the modeller can control the polarity of live frogs and operate panel indicator lights at the same time. Other uses include signal interlocking and reverse loop switching. For the advanced modeller. | |
more | Peco Probe for electrically operating Points (PL17)
Use in conjunction with PL-18 studs to electrically operate points. | |
more | Peco Studs and Tag Washers (PL18)
Studs & Tag Washers | |
more | Peco Track Isolating Switch On-Off (PL20)
Simple to clip onto Streamline track in conjunction with an isolating rail joiner to provide simple isolation of track sections, or can be used as an on-off switch on control panels. In plastic case. Easy action. | |
more | Peco Four Pole Double Throw Switch (PL21)
A special on/on, panel mounting, 12 tag toggle switch required when using Peco's N gauge scissors crossing (SL-E383E). A different style to other Peco switches and a most useful item with many uses around the layout. | |
more | Peco Switch - Single Pole On - Off (PL22)
Use this switch for controlling isolated sections of track such as those found in locomotive depots, bay platforms, etc, or to operate lights and motorised scenic accessories. | |
more | Peco Changeover Switch - Single Pole On-On (PL23)
Use this switch to control colour light signalling or use two ganged together as a polarity reversing switch to control reverse loops, turntables etc. | |
more | Peco Switch Lever Joining Bars (PL24)
| |
more | Peco Passing Contact Switch Black Lever (PL26B)
This switch provides the short burst of current needed operate the popular PL-10 point motor. May be ganged using the PL-24 joining bar with either of the other two types of switch to provide signal interlocking, panel lights etc. | |
more | Peco Passing Contact Switch Red Lever (PL26R)
This switch provides the short burst of current needed operate the popular PL-10 point motor. May be ganged using the PL-24 joining bar with either of the other two types of switch to provide signal interlocking, panel lights etc. | |
more | Peco Passing Contact Switch White Lever (PL26W)
This switch provides the short burst of current needed operate the popular PL-10 point motor. May be ganged using the PL-24 joining bar with either of the other two types of switch to provide signal interlocking, panel lights etc. | |
more | Peco Passing Contact Switch Yellow Lever (PL26Y)
This switch provides the short burst of current needed operate the popular PL-10 point motor. May be ganged using the PL-24 joining bar with either of the other two types of switch to provide signal interlocking, panel lights etc. | |
more | Peco Switch Console (PL27)
A six bay console to take PL-22, 23 or 26 switches. Suitable for use in banks. | |
more | Peco Switch Mounting Plate (PL28)
Mount switches into a `mimic' diagram or update an existing control panel. | |
more | Peco Terminal Connectors and Shrouds (PL31)
Push-On, easy to use, no soldering required | |
more | Peco Microswitch Open Type (PL32)
These useful switches are similar to those used in the PL-15 twin microswitch kit. Rated at 16 volts with 2amp continuous useor 2.5 amps passing contact. Two per pack. | |
more | Peco Microswitch Enclosed Type (PL33)
The smallest of microswitches, only 12mm long and weather resistant as used in the Gauge O FB points. Rated at 16volts with 2 amps continuous or 2.5 amps passing contact. One per pack | |
stock
info | Peco Capacitor Discharge Unit CDU (PL35)
The Peco capacitor discharge unit is supplied in a neat plastic box with quick clamp type connectors, ready for installation. | |
more | Detail Matters Metal Underboard Mounting Plates (6) for PL10 Point Motor (SR1m)
Pressed metal mounting plates designed to allow the Peco PL10 point motor to be fixed beneath your layout board. Supplied with mounting screws.more.. | |
more | C&L Finescale Tortoise Slow Action Point Motor (C1540)
| |
more | Detail Matters Capacitor Discharge Unit CDU (H40)
A capacitor discharge unit is used to help ensure that point motors receive a good voltage when the control switch is thrown. This helps ensure that point motors throw properly in answer to the control switch.
Due to exposed terminals and the possibility of receiving an electric shock from the charged capacitor the CDU should be fitted inside an enclosure while in use. | |
more | Peco Point (Turnout) Motor (PL10)
The point motor attaches directly to the underside of the turnout to ensure positive and reliable operation. Requires a 40 x 25mm hole in the baseboard to accomodate the motor. Operation is from a passing contact switch or probe and stud system to give a pulse from the 16v AC outlet found on most transformers (2 amps required). If this isn't available an uncontrolled 12v DC supply may suffice. A constant current would burn out the motor. | |
more | Peco Side Mounted Point (Turnout) Motor (PL11)
This point motor is designed to mount alongside a point, avoiding the need to cut a hole into the baseboard to fit a motor below each point.
Note that the green wire is the common return wire. | |
more | Peco Mounting Plate for G-45 Turnout (PL8)
| |
more | Hornby Passing Contact Lever Switch for Points (R044)
For operating point motors - passing contact to give a single pulse. | |
more | Hornby Two Way Lever Switch On-On Yellow (R046)
Used to transfer power from one circuit to another, eg. colour light signals & turntables | |
more | Hornby Lever Switch On/Off for Lights etc (R047)
For switching power on & off | |
more | Hornby OO Point Motor (R8014)
Powerful solenoid point motor, may be mounted above or below baseboard, powered from 16v AC supply. Requires Passing Contact Lever Switch (R044) | |
more | Hornby OO Point Motor Housing (R8015)
For fitting point motors above baseboard | |
Model Railways
Search
Index
Checkout
Back